Composite mesh
with integrated spacers
Designed to replace the traditional metal mesh. The mesh does not undergo deformation during installation and can withstand the weight of a person - that is, when molding the panel, installers can walk on it without restrictions. At the same time, its feature allows for uniform installation and strong fixation in the concrete layer.
What properties does composite reinforcement have?
Corrosion and chemical resistance
No fear of chemical impact and moisture, which affects the durability of the use of materials, and the possibility of their use at any time of the year
Does not form "thermal bridges", which improves the thermal insulation parameters of the construction site
Low thermal conductivity
Even in severe frosts, composite reinforcement does not lose its properties. The temperature threshold for use ranges from -70°С to +100°С
Heat resistance
The lack of need for welding simplifies the installation — with wire-tying reinforcement, any worker can handle it with a minimum set of tools
Easy to install
Dielectric, no radio interference
Does not conduct electricity and does not interfere with the spread of the signal of mobile phones and the Internet
Tensile strength
The tensile strength of composite rods and mesh is 3 times higher than that of a similar steel product
Shear strength
The shear strength of the composite mesh rods is the same as that of the similar steel products
Used for thin-walled concrete structures
Composite mesh SIREP is designed to replace traditional galvanized or stainless steel mesh when reinforcing a variety of different thin-walled concrete structures
Reducing the thickness of the facade layer
Using composite mesh SIREP for thin-walled concrete structures on the facade layer of the panel will reduce its thickness from 80 mm to 40 mm
Advantages for thin-walled concrete structures
By reducing the thickness of the facade layer from 80 mm to 40 mm
Reduced panel weight
Reduced panel costs
By reducing the weight of the panel, the volume of materials required for the production of one panel is reduced
Improving logistics
Reduced spendings on transportation, by reducing weight and panel thickness
Reduced of construction volume
The total cost of construction of buildings and structures is reduced
Up to 4% additional square meters of living space
Additional square meters of living space by reducing the thickness of the facade layer of the panel
Increase in number of floors / decrease in foundation costs
The load on the foundation is reduced, that allows to either save on the foundation, or increase the number of floors of the building
Comparison of composite and steel mesh
Steel mesh from wire Vr-1 GOST 23279
Composite mesh produced by AO RPP
Characteristics of materials
* according to research by the Norwegian Institute
1200
BREAKING STRENGTH, MPA

570
720
BREAKING REINFORCEMENT OF RODS, KGS

760
56
COEFFICIENT OF THERMAL CONDUCTIVITY

0,46
2220
WEIGHT OF UNIT AREA, G/M2

360
Up to 600°С
RESISTANCE TO FIRE

Highest fire safety*,
more than 300 ° С
Electroconductive
ELECTROCONDUCTIVITY
Dielectric
Magnetoinert
MAGNETIC CHARACTERISTICS
Magnetizes
Heat-conductive
THERMAL CONDUCTIVITY
Non-heat-conductive
Susceptible to corrosion
CORROSION AND CHEMICAL RESISTANCE
High corrosion and chemical resistance
More advantages of composites over metals
Composite armature is cheaper than metal armature and its high strength makes it possible to replace a steel analogue with a large diameter
Reduced material consumption
Reduced transportation costs
Thanks to the compact form of packaging, it is much easier to transport such a reinforcement - you can use the trunk of any car
Expansion coefficient like concrete's
There is no imbalance in the reaction of concrete and composite reinforcement with temperature changes - this helps to protect concrete structures from cracking
Low relative density
Having a low weight, composite reinforcement does not create unnecessary loads on the main elements of the structure - it can be used where it is impossible to use metal
Energy efficiency
Heating costs for a building constructed using composites are lower compared to steel reinforcement
Waste-free utilization
The flexibility of the reinforcement makes it possible to reduce the amount of waste down to "No Waste", while waste is certainly present when using metal
Get product samples
We're confident in the quality of our products, because we comply with all legal requirements for composite building materials. You can also make sure by ordering samples with delivery
© 2017–2022 AO RPP.
The information provided on the site is not a public offer
428008, Chuvash Republic,
Cheboksary, st. Kombinatskaya, 4
428003, Chuvash Republic,
Cheboksary, Kabelny proezd, 3
info@sirep.ru
+7 (8352) 36-49-48
NAVIGATION
INFORMATION
CATALOG
STAY INFORMED ON OUR LATEST NEWS